Cart - $0.00

You have no items in your shopping cart.

YouTube Facebook Twitter 888-524-7921 Email Us

SW-MOTECH Handlebar risers for most BMW, Ducati, Kawasaki, KTM LC4, Gas-Gas, Honda, MZ, Suzuki, Triumph & Yamaha, rise height of 20mm, 25mm, 30mm or 50mm

SKU: LEH.00.039150

In stock

* Required Fields


Provides a more upright, comfortable riding position by raising the original 7/8" (22mm) diameter tubular handlebar.

These high quality bar risers increase comfort, look great, and are easy to install.

No need to replace your handlebars. Simply remove the original top clamp, place the riser between the handlebar and original bottom clamp, and install the top clamp using the included hardware. For use with original top clamp or included matching SW-MOTECH top clamp. Available in anodized silver or black.

Rise height available:
20mm (0.8"), 25mm (1"), 30mm (1.2"), or 50mm (2").
NOTE that not all riser heights will fit on every motorcycle. Contact us and we will help you select the best option.

No change of control cables, wiring, or hoses is required for most motorcycle models for 20mm, 25mm, or 30mm handlebar risers. HOWEVER: The installer should always check for adequate cable/wiring/hose slack after installing any handlebar riser!

Simply put, the amount of cable slack varies on factory bikes even within a single model and year, so while 99.9% of all bikes will not need adjustment of cables to install handlebar risers, you should ALWAYS check for adequate slack after installation.

Please follow all Torque Specifications! Failure to do this will void warranty. See installation instructions.

What's in the Box:

  • 1 pair of riser blocks 
  • 1 pair of top clamps
  • 2 sets of screws 

Please note:

  • 20 mm height risers include four M8x55 screws and four M8x60 screws.
  • 25mm height risers include four M8x60 screws and four M8x65 screws.
  • 30mm height risers include four M8x65 screws and four M8x70 screws.
  • 50mm height risers include four M8x90 screws.

Customer Testimonial: John G - I purchased the 30MM risers for my '09' KLR650 and they work great. I don't think I could have gone higher. The electrical leads were almost maxed out. I took a 250 mile road trip and the risers relieved the tension in my shoulders and upper back that I have had on long trips in the past. I would recommend these riser for serious riders.

This riser will fit your bike if:

(1) Your bar mounts are symmetrical and parallel;
(2) Your bars are 7/8" outer diameter;
(3) You have two M8 (8mm-diameter holes with standard M8 thread pitch) threaded holes in each of your two bar mounts; and
(4) The distance between the two holes in a single bar mount is 31-37mm on center. The distance between the two bar mounts is not a factor.

These handlebar risers will only fit standard handlebar mounts that are symmetrical and perpendicular to each other; as such, these handlebar risers will not fit the Kawasaki Z1000, Kawasaki Z750S, or any other motorcycle with asymmetrical handlebar mounts.
If your handlebar mounts don't look similar to those pictured on this page, please contact us before ordering to confirm that the item will fit your bike.

NOTE that not all riser heights will fit on every motorcycle. Contact us and we will help you select the best option.

Confirmed fit list:

Pegaso 650, -'00

F650 Funduro, -'00 (does NOT fit F650GS models)
F650/ST, -'00 (does NOT fit F650GS models)
F800ST, '07- (20, 25, or 30mm rise height)
R80GS/ST, '80-'87
R1150GS (extension of front brake hose required)
R1150GS Adventure
R1150R Rockster
R1200RT, '05-
K1100RS, '02-

Gran Canyon 900, '98-

Multistrada DS1000 and DS620 (requires add-on Ducati screw kit)

599 (CB600 Hornet, naked model)
919 (CB900 Hornet, naked model)
NT700V Deauville
ST1100, '91-'94 (silver) (cannot use with stock handlebar plastic cover)
ST1100, '95- (black) (cannot use with stock handlebar plastic cover)
All Nighthawk models

Eliminator 125
ER6F Ninja 650R, '06-'08
KLR650A '87-07
KLR650E '08- Up to 30mm without changing cables.
Versys 1000 '12-
Vulcan 750
ZR 750 Zephyr
ZRX1200R (control cable extensions may be required)
DOES NOT FIT Z1000 or Z750S!
DOES NOT FIT '09- Ninja 650!

LC4 with tubular 7/8" diameter handlebars (measure hole distance before ordering)


DL650 V-Strom, '04- (non-ABS)
DL650 V-Strom, '04- (ABS model requires an upper front brake line extension for installation of risers larger than 20mm)
DL1000 V-Strom, '02-
DR650SE, '96-
GS500E '90-'06
GSF600 & GSF600/S Bandit, all years
GSF650 & GSF650/S Bandit, all years
GSF1200 & GSF1200/S Bandit, all years
SV650N, -'02 (not for SV650S faired model)
SV650N, '03- (not for SV650S faired model)
SV1000N, '03- (not for SV1000S faired model)

Adventurer 900
Bonneville 800
Legend TT 900
Scrambler 865, '07
Tiger 1050, '07-
Tiger 955i, ’01-'06
Tiger 900, -‘01
Trident 750 & 900
Speed Triple 750, 900, 955i
Speed Triple 1050, '-07 (note: a rise height of more than 20mm requires a brake extension) 2008 and later model has 28mm bars and will not work with these risers
Street Triple 675, '08-'10 the Street Triple "R" model has 28mm bars and will not work with these risers

Note: Triumph bikes require optional screw kit that are 5mm shorter than those packed with the "universal" kit, which contains four M8x65 and four M8x70 screws.

FZ1, '01-'05 - no extension needed
FZ1, '06-'10
FZ6, '04-'10
FZ8, '11- (20mm rise height only)
V-Max 1200, -'07

Customer Reviews
Review by agtheokie
Went perfect on my 2013 fz8 to adapt fz1 flat bars to the bike. You need the .08 (20mm) risers so master will clear. I chose black, as i had painted the bars black. Great fit, close tolerance which is very nice. (Posted on 15-03-16)
Review by jer
I bought the 0.8 inch bar risers for my 2013 Yamaha FZ8, this seems to be the biggest you can get with stock brake lines, etc. It went on easy and it seems to be helpful. I have problems with my left arm so any less of a reach would be helpful for that. It's not so much of a change that I expect anyone would notice it. (Posted on 14-12-03)
Review by wl7cpa
I put this on my 2013 Gladius SFV650A Suzuki. They work great. Any taller and I think cables would not go right, have to replace or lengthen. (Posted on 14-09-24)
Review by LarryG
Easy 10 minute install. Perfect addition with my street fighter handlebars. NO NEED to purchase longer screws, the riser kit comes with perfect fit hardware. Great purchase! (Posted on 14-08-27)
Review by Anonymous
Easy Install and just the right realignment of the bar (Posted on 14-07-07)
Review by a1b2c3
Fit right on without any mods to wiring or cables. It is amazing what a difference 1-inch makes when riding standing up. Be careful not to buy a set of bolts you don't need. (Posted on 14-07-07)
Write Your Own Review

Only registered users can write reviews. Please, log in or register